Crash Course in Fixing a Lava Lamp

At work, I have a co-worker that's a garage-sale-aholic. She had this lava lamp on her desk that she rescued after being shaken, but it had started turning itself off and she had to bang it to get it to work again. Finally it turned off all together. We were talking, because she had another and I told her I should really get one for my cube, she pointed to the broken one and said "if you can fix it, you can have it." 

So I accepted the challenge. I took the lava lamp back to my desk and on my lunch hour I started messing with it. I found that if i pressed on the bottom, the light would turn back on. So i pulled off the felt and found a bolt, which i then tightened and voila! the lava lamp worked again. The fix took about two minutes total. 

I went over to her and told her i fixed it. This was met with a chorus of NUH UH!s from the group that had been contemplating the broken lava lamp for months. But even though i offered the lava lamp back (It's very pretty, yellow wax with purple water, makes the wax red when it gets towards the top oddly enough), she said i should keep it since we had a bargin. So i had a lava lamp at my desk, much to my enjoyment.

After about a week, I started noticing that the lava lamp would periodically turn off and back on after about a minute. Pretty soon, I was tapping the base, just like she had described. So i took the felt off again and tried to tighten the bolt again, only this time, the whole thing turned off completely and wouldn't turn back on. Whoops. 

Since i wasn't about to give up on this lava lamp, I tried to get inside. When you took out the bulb, there was a golf ball sized hole where you could see the porcelain socket. But the bottom had a steel plate with a hole the size of an eraser head with the bolt coming through and that was it. The base was not designed to come apart. Probably smart on the part of the manufacturer, but very annoying for me. So armed with a needle nose pliers, a small screw driver, a flat staple remover, an unbent paper clip, and a surgical style clamp (like they use in surgery) I began the very tricky task of fixing the lava lamp base.

Once i unscrewed the bolt in the bottom, the socket fell loose and rolled around inside. It was then that i could see that one of the wires had popped completely off the socket. So that was the problem. Ok, I knew how to re-wire a lamp. Somehow, through this golf ball sized hole, i would have to manipulate the socket, screw, and wire all back into their proper places.

It was far from easy. Took me a full lunch hour and a break, significant muttering under my breath, and getting VERY creative with some angles and my tools. The wire wouldn't slide into the base any further, so i had to work inside the tiny cone. Finally,  the wire was looped back around the screw and re-tightened. I put the socket back into place, tightened the bolt, and put the bulb back in. 

The moment of truth, i spun the switch and....nothing. I couldn't understand it. It was still broken! The configuration wasn't that complex, two screws, two wires, and a bolt. After more fiddling after work, the stupid thing still wouldn't work. So i went home for the night. 

It bothered me, as i laid in bed. I thought about how to fix the lava lamp. I knew that the lamps were only about 20$ and this really wasn't worth the effort. But now it was personal. I was going to fix it. 

So as i went about my morning routine and the routine at work, it continued to infest my mind. If i had been smart, i would have put it out of sight, but i had left it in my line of vision where it normally stood. So on my first break, i started fiddling with it again. Checked the bolt, checked the switch, checked the wires, checked that the bulb wasn't burnt out. 

By all reasoning, the lamp should have worked! Maybe the wire was bad, so i followed it, all the way down to the power strip where it was plugged in. 

Inspecting this led to a revelation. The on light on the power strip wasn't on. It couldn't be that easy could it? A short? I flipped it off and back on. No change. I switched the plug to the other one in the pair; still nothing. Finally i moved it over to the other plug i KNEW worked. The power strip lit up, and as i peeked over the edge of my desk and was blinded by the base since it was facing me with the bulb in it. 

Shortly there after, i had re-assembled my pretty lava lamp and the whole thing worked fabulously. My lava lamp is fixed. And with any luck...will stay that way for a change. 

I'm thinking about changing its name from Trippy the Lava Lamp to something a little less polite.